#	Make	System Type	Special Functions
1	Mercedes-Benz	Drive	Initial startup
2			Control unit adaptations
3			Read coding and change if necessary
4			Read coding and/or transfer download to new control unit
5			Replace component Y74 (Pressure control valve)
6			Replace component B28/8 (Pressure differential sensor (DPF))
7			Learning of the throttle valve stop
8			Learn air conditioning
9			Activate fuel pump
10			Adjustment On temperature of heater booster(Electric heater booster)
11			Injector classification/Injector shutoff
12			Transmission oil temperature
13			Emergency running
14			Display adaptation data
15			Resetting of adaptation data
16			Performing adaptation
17			Coding according to plant data
18		Chassis	Initial startup
19			Control unit adaptations
20			Road test
21			Learning processes
22			Resetting of variant locking
23			Erase zero point offset error of component N49(steering angle sensor)
24			Deactive system
25			Active system
26			bleed brake system
27			Calibration of the plunger travel sensors
28			Level calibration
29			Load adjustment
30			Replacement of component B24/15
31		Body	Initial startup
32			Control unit adaptations
33			Read coding and change if necessary
34			Coded vehicle data
35			Variant coding
36			Chassis number
37			Setting of limit position of excess force limiter
38			Zero position adjustment
39			Panornamic sliding roof
40		Information and Communication	Initial startup
41			Control unit adaptations
42			Read coding and change if necessary
43			Assyst Setting
44			General servicing
45			confirm overall maintenance
46			Oil change
47			Clock Setting
48			Reset odometer to 0 km
49			Radio parameters
50			TV parameters
51			TV Active
52			Restart of optical ring
53		Seats and doors	Initialization of power closing
54			Read coding and change if necessary
55			Normalize left power window
56		Air Conditioning	Initial startup
57			Read coding and change if necessary
58			Normalizing of position motors
59			Check of adjustment range of postioning motors
60			Variant coding
61			Control unit reset
#	Make	System Type	Special Functions
1	BMW	Drive	DME-CAS Adjustment
2			Idle speed Adjustment
3			Clear adaptations
4			Learning Valvetronic limit positions
5			CO adjustment
6		Chassis	Adjustment,steering-angle sensor
7			Bleeding,DSC hydraulics
8			Mix-up checks,brake lines
9			Start startup
10			Learn sensor values
11		Body	Run-in protection for A/C compressor
12		Service functions	Reset service interval indicator
13			Read out operating data
14			Engine oil
15			Microfilter
16			Front brake
17			Rear brake
18			Diesel filter
19			Spark plugs
20			Coolant
21			Brake fluid
22			Vehicle check
23			Vehicle inspection
24			Exhaust emission inspection
25			Delete transport mode
#	Make	System Type	Special Functions
1	VOLVO	Drive	Quick test of the fuel tank system
2			Quick test of exhaust camshaft control
3			Quick test of intake camshaft control
4			Quick test of fuel pump(FP)
5			Quick-test injectors
6			Readiness Code
7			Adaptation of the throttle unit
8			Resetting the adaptation values
9			Resetting the odometer particle trap
10			Adaptation of the exhaust gas recirculation(EGR) valve
11			Initializing the window position
12			Resetting the service reminder indicator
13			Combustion of soot particles, particle trap
14			Programming the optimizing parameters
15			Programming the remote control setting
16			Resetting Adaptation
17			Resetting the odmometer particle trap
18			Testing all needles and lamps in the dashboard
19			Programming the driver information module(DIM)
20			Resetting counter oil
21		Chassis	Calibration of position sensor
22			Resetting adaptation
23			Resetting counter oil
24			Calibration(Cars with DSTC)
25			Control module adaptation
26			Resetting adaptation to zero
27			Resetting the counter for -Gearbox oil change
28			Check brake light switch adjustment
29			Calibration
30			Reading off the configuration
31			Resetting the service reminder indicator
32			Initial adaptation
33		Body	Refilling the feed hose with additive
34			Resetting the tank level gauge
35			Initializing the window position
36			Programming the remote control setting
37			Calibration of position sensor,GDL lamps
38			Qick test of alternator function
39			Resetting low voltage counters
40			Resetting crash mode
41			Programming of rear window wiper when reversing
42			Reinstalling the reserve battery
43			Programming the infotainment control module(ICM)
44			Calibrating the Climate Control Module (CCM)
45			Identifying the Damper Motor Module (DMM)
46			Programming remote control setting
47			Resetting low voltage counters
48			Ignition switch key position
49			Resetting crash mode
50			Resetting low voltage counters
51			Resetting factory settings
52			Programming the control module
53			Reading off the alarm cause
54			Resetting the car
55			Volvo On call service check
56			Reinstalling the spare battery
57			Resetting the carphone code
58			Calibrating the position sensor for Bi-Xenon lamps
59			Adjusting ECC parameters
60			Calibrating the occupant weight sensor(OWS)
61			Activation and service
62			Reading off programmed values
63			Checking current values
64			Storing the ID number for the occupant weight sensor (OWS)
#	Make	System Type	Special Functions
1	VW/AUDI/SKODA/SEAT	Drive	Throttle Adjustment
2			Electronic throttle (kickdown switch adaptive)
3			Clear the value of self-learning
4			EGR Adaptive
5			Fuel injection (pump adaptive)
6			Emergency diesel particulate filter regeneration
7			Camshaft adjustment
8			Oxygen sensor control
9			Idle adjustment
10			Adaptive matching target idle
11			ECU computer programming
12			Automatic transmission basic settings
13			Automatic transmission computer programming
14		ABS	Steering angle sensor zero
15			Lateral acceleration sensor adjustment (G200)
16			Brake pressure sensor adjustment (G201)
17			Longitudinal acceleration sensor adjustment (G251)
18			Anti-lock brake system Exhaust
19			Anti-lock brake system computer programming
20			ESP (electronic stability system) driving test initialization
21			ESP (electronic stability system) Steering angle sensor calibration
22		Body	Airbag control unit programming
23			Balloon release and activation
24			Maintenance light reset
25			Fuel level sensor adaptive
26			Dashboard Language Settings
27			Security and key match
28			Air Conditioning Basic Settings
29			Remote keyless Clear/match
30			Replace the brake pads
31			Headlight position adjustment self-learning
32			Suspension Level Control Calibration
33			Tire adaptive
#	Make	System Type	Special Functions
1	PSA	Drive	Particle filter regeneration
2			Self-adaptation reset
3			EGR SV learning
4			EGR throttle learnng
5			Initialization turbo limit
6			Particle filter regeneration
7			Particle filter replacement
8			Initializ.FAP filter additive quantity
9			Replace or fill additive tank
10			Replace metering pump
11			Tank filling
12			EGR throttle initial. and intake air heat
13			Timing correction
14		ABS	Bleeding
15			Steering angle calibration
16			Rear RH Wheel bleeder
17			Rear LH Wheel bleeder
18			Front LH Wheel bleeder
19			Front RH Wheel bleeder
20		Body	Configuration
21			Forcing of the customer mode
22			Resetting to zero of the service mileage
23			Configuration
24			Programming of the build-in systems interface (Engine Immobilizer code and keys )
25			Resetting_zero_service
26			Reset maintenance indicator
27			Reset maintenance mileage
28			Reset maintenance number done
29			Reset maintenance mileage and number
30			Service Reset
#	Make	System Type	Special Functions
1	OPEL	Drive	APP Learn
2			Clutch Pedal Position Learn
3			DPF Pressure Sensor Learn
4			Exhaust Gas Temperature Sensor Learn
5			H02S Learn
6			MAF Sensor Learn
7			EGR Valve Learn
8			Fuel Rail Pressure Sensor or Fuel Rail Learn
9			Crankshaft Position Reluctor Wheel Learn
10			Turbocharger Learn
11			Flywheel Learn
12			DPF Reset
13			Catalyst Reset
14			Engine Oil Life Reset
15			Glow Plug Control Module Reset
16			Regeneration Disel Particulate Filter
17			Crankshaft Position Variation Learn
18			HO2S Heater Learn
19			Fuel Trim Reset
20			Regeneration DPF
21			Inject Cutoff Test
22			RPM Control
23			Program Idle Speed
24			Adjust Idle Speed
25			Idle Learn
26			Reset Learned Values
27			Reset O2-Loop Block Learn Map
28			Programming
29			ECU Control
30			Program High CanBus Configration
31			Replace Rail Pressure Sensor
32			Replace Diff.-Press. Sensor
33			Program High Speed CAN-Bus Configuration
34			Reset ECU
35			Program Injector
36			Replace Injector
37			Replace Diesel Particulate Filter
38			Replace Mass air flow sensor
39			Replace Precatalyst
40			Replace Rail Progressure sensor
41			Reset Engine Oil Life
42			Regeneration Diesel Particulate Filter
43			Replace 02 Sensor
44			Replace 03 Sensor
45			Reset O2 sensor
46			Replace Disel Particulate Filter
47			Injector Cutoff Test
48			Regeneration D. Particulate Filter
49			Replace DPF
50			EGR Control
51			Replace Fuel Pump
52			ECU Reset
53			Replace MAF Sensor
54			Injector Cut Off Test
55			Electronic throttle control
56			Idle speed program
57			Fuel Tank Ventilation Control
58			Reset Oil Life
59			Reset engine oil sensor
60			Program High Speed Can Bus Config
61			Idle Speed
62			DPF Regeneration
63			Reset Learn Values
64			Program High Can Configuration
65	Gear Selector N Position Learn
66	Learned Values Reset
67	Chassis	Brake Pressure Sensor Calibration
68		Yaw Rate Sensor Learn
69		Steering Wheel Angle Sensor Learns
70		Brake Pedal Position Sensor Calibration
71		Steering angle calibration
72		Steering Angle Sensor Calibration
73	Body	Brake Pedal Position Sensor Learn
74		Clear Driver Window Learn Values
75		Clear Left Rear Window Learn Values
76		Clear Passenger Window Learn Values
77		Clear Right Rear Window Learn Values
78		Program Transponder-Keys
79		Calibration
80		Erase Transponder-Keys And Remote
81		Program Transponder-Keys And Remote
82		Service Light Reset
83		Service Due In
84		ECU Control
85		Erase Key Set
86		Erase Remote Keys
87		Program Remote Key
88		Clear Deployment Record
89	Service functions	Power Steering Softstops Reset
90		Power Steering Softstops Learn
91		Park Brake Calibration
92		CAN Bus Configuration Learn
93		HVAC Actuators Learn
#	Make	System Type	Special Functions
1	LandRover	Drive	Powertrain control module adaption clear
2			Powertrain control module adaption
3			Fuel prime routine
4			Diesel particulate filter replacement
5			Reset the oil service counter
6			Transmission control module adaption clear
7			Gear selector sensor calibration
8			Sunroof calibration.
9		Chassis	Longitudinal accelerometer calibration
10			Longitudinal accelerometer sensor calibration
11			Lateral accelerometer calibration
12			Pressure sensor calibration
13			Yaw Rate sensor calibration
14			Roll Rate sensor calibration
15			Drive the parking brake to the mounting position
16			Drive the parking brake to the latching position
17		Body	Seat cushion replacement
18			steering angle sensor calibration
19			service interval reset
20			Sliding roof module initialisation
21			Rain sensor initialisation
22			Driver's memory seat calibration
23			Headlamp control module system calibration
24			Driver's door window glass.
25			Driver's seat calibration.
26			Stepper motor replacement
27			Seat heater module calibration
28			Hunidity sensor replacement
29			Passenger's door window glass
#	Make	System Type	Special Functions
1	Europe Ford	PCM	Fuel injector correction factors
2			Fuel Injector Coding
3			Diesel particulate filter static regeneration
4			Reset the Intake Air Throttle Valve Learned Values
5			Reset the Exhaust Gas Recirculation Valve Learned Values
6			Reset the Diesel Particulate Filter Learned Values
7			Reset Differential Pressure Sensor Learned Values
8			Reset the water in fuel Warning Indicator
9			Reset the Mass Air Flow Sensor Learned Values
10			Reset the Heated Exhaust Gas Oxygen Sensor Le
11			Reset the Air Conditioning Compressor Learned
12			Reset the Exhaust Gas Temperature Value
13			Reset the Fuel Injection Pump Learned Values
14			Reset the Knock Sensor Learned Values
15			Reset the Fuel Metering Valve Learned Values
16			Reset KAM
17			Key Programming
18			Initialize the Exhaust Gas Related Component
19		ABS/EPS	Configure the lateral acceleration sensor
20			Configure the steering angle sensor
21			Configure the yaw rate sensor
22			Pressure Sensor Calibration
23			Configure the longitudinal acceleration sensor
24			Pressure calibration sensor
25			Side acceleration sensor calibration
26			Steering angle calibration
27			Yaw sens.calibration
28		PATS	Key Programming
29		RCM	ECU ID Data
#	Make	System Type	Special Functions
1	Renault	Drive	Configuration
2			Injector command lock
3			cylinder 1 injector code entry/reading
4			cylinder 2 injector code entry/reading
5			cylinder 3 injector code entry/reading
6			cylinder 4 injector code entry/reading
7			Accessories disconn.: Active
8			Accessories disconn.: Inactive.
9			New pump carter filling
10			Save routine
11			Self-adjust AGR
12			Self-adjustment pressure ctrl.
13			A/T lever block SV (shiftlock)
14			Actuators Control
15		Chassis	Steering angle sensor initialisation
16			Speed index
17			Vehicle parameters
18			Prevention of stop light auto illumination
19			Auto stop lights illumination authorisation
20			Esp automatic reconnection threshold
21			Write date of last after sales operation
22			Vehicle speed at initialisation
23			Last intervention date setting
24		Body	Brake lining friction learning
25			Configuration
26			With tyre pressure monitoring
27			Without tyre pressure monitoring
28			Lock computer
29			Unlock computer
30			Oil change interval in km
31			Oil change interval in months
32			Oil change range : current value in km
33			Oil change range : current value in months
34			Update odometer
35			Vehicle type megane/scenic
36			Vehicle type megane with pax tyres
37			Vehicle type vel statis
#	Make	System Type	Special Functions
1	Toyota/Lexus	Drive	Check Mode
2			Reset Memory
3			VIN(VIN Read,VIN Write)
4			Electric Throttle Learning
5			Deceleration Sensor 0 Point Calibration
6			CVT Oil Pressure Calibration
7			Read Freeze Frame Data
8			Clear the fault reason code
9			DPF Deterioration Record Clear
10			A/F Sensor Compensation Reset
11			Crank Time Compensation Reset
12			Catalyst Record Clear
13			Supply Pump Initialization
14			Vehicle Mileage Write
15			Injector Compensation
16			Pilot Quantity Learning Values Reset
17			Catalyst Record Read
18			Catalyst Record Transferring
19			Check secondary air injection
20			Pressure Discharge Valve Check
21			Pilot Quantity Learning
22			CVT hydraulic learning
23			Auxiliary pump learning value is initialized
24			A/T Code Reset
25			A/T Code Registration
26			Read Freeze Frame Data
27		ABS/VSC/TRC	Air Bleeding
28			Reset Memory
29			Test Mode
30			ECB Utility(ECB Invalid,Zero Down,Linear Valve Offset)
31			Linear pump learning value is initialized
32			Backup storage Clear
33			Accumulator to zero relief driver
34		AFS	ECU Information Synchronize
35		EMPS	Steering angle sensor output learning
36			Torque Sensor Adjustment
37		Tire Pressure Monitor	ID Registration(Main Set,2nd Set)
38			Logo registration
39		Body	Initialization
40			Wireless Code Erasure
41			Wireless Code Registration
42		Immobiliser/Remote Engine Starter	Key Code Registration
43			Key Code Erasure
44			Auto Registration Closure
46			Trouble Factor Code Clear
47			Transponder Code Erasure
48			Transponder Code Registration
49			ECU Communication ID Registration
50			Communication Check(Key Diagnosis Mode)
51		Others	Compass calibration
52			Initialization
53			Parts Exchange
54			Axis Adjustment
55			Steering Angle Adjust
56			Servomotor
57			Recognition ECU High Temp History Reset
58			Camera/Target Position Memory
59			Camera Axis Adjust
60			Rear Beam Axis Adjustment
61			Camera Angle Adjustment
62			VIN Read
63			Starter Exchange
64			Reset A/C Information
65			ECU Exchange
#	Make	System Type	Special Functions
1	Honda/ACURA	PGM FI	TP sensor reset
2		ABS TCS VSA	All sensor calibration
3		BODY	Gauge Control Module Replacement
4			Power Window Reset for Driver side
5			Power Window Reset for Passenger side
6			Power Window Reset for Left side
7			Power Window Reset for Right side
8		IMMOBI	Add keys
9			Rewrite keys
10			All keys lost
11			Delete Keys
12		SRS	OPDS init
#	Make	System Type	Special Functions
1	Mitsubishi	MPI/GDI/DIESEL	Provisional DTCs
2			Learned value reset
3			Timing chain maintenance
4			Coding
5			Engine Test
6			DPF regeneration
7			Learning
8			Initialization
9			INJ.ID Writing(Exchanging INJ.)
10		AT/CVT/A-MT/TC-SST	Provisional DTCs
11			Learned value reset
13		ABS/ASC/ASTC/WSS	Emission Gas Mode
14			SAS Calibration
15			Yaw rate sensor type reset
16			Sensor calibration
17			Air bleeding
18			valve_pressure_learing
19		Body	Service reminder
20			Rain Sensor Adaptation
21			Customization Information
22			Customization Reset
23			Theft alarm
24			Key Program
#	Make	System Type	Special Functions
1	Nissan	Engine	TP/SW SEN IDLE POSI ADJ
2			IGNITION TIMING ADJ
3			FUEL PRESSURE RELEASE
4			IDLE AIR VOL LEARN
5			TARGET IGN TIM ADJ
6			TARGET IDLE PRM ADJ
7			NISSAN NATS(I-KEY)
#	Make	System Type	Special Functions
1	SUBARU	Engine	Dealer Check Mode Procedure
2			System Operation Check Mode
3			Diagnosis Results
4		AT	Fuction Check Sequence
5		Chassis	Freeze Frame
6			Fuction Check Sequence
7		Body	Freeze Frame
8			Compulsory Height Control
9			Variable compressor break-in drive
10			ECU Customize
11			Function check menu
12			Sensitivity Adjustment Mode
13			Sensor initial setting
14			Collation ECM output check
15			Keyless access system check
16			Power supply ECU output check
#	Make	System Type	Special Functions
1	ISUZU	Engine	Injector ID Code
2			ID Code Registration
#	Make	System Type	Special Functions
1	HYUNDAI	Drive	Resetting adaptive values
2			Idle CO adjustment
3			Resetting auto T/A values
4			Freeze frame data
5			EVAP.test(dmtl test)
6			Version configuration
7			Readiness test
8			PCM auto detection reset
9			PCM lock(MEC) setting
10			PCM auto detection reset
11			Resetting Auto T/A Values
12			Resetting adaptive values
13			CPF service regeneration
14		Chassis	Air bleeding mode
15		Body	Crashing information
16			Active DTC information
17			History DTC information
18			Password /changing
19			Teaching
20			Neutral mode
21			Limp home mode
22			Learning mode
23			Smarter neutral
24			Resetting adaptive values
25			Idle CO adjustment
26			Version configuration
27			Passanger airbag realtime info
28			Password recored/change
29			Master key record/change
30			Master key delete
31			Immobilizer reset
32			Air bleeding mode
33			Passanger airbag real time info
34			Lock/unlock alarm
35			Arm/disarm by key
36			Auto door lock
37			Get in or get down link age
38			Pods reset
39			Password changing
40			Warning status(high-line)
#	Make	System Type	Special Functions
1	KIA	Drive	Resetting adaptive values
2			Idle CO adjustment
3			Freeze frame data
4			Monitoring test(euro.only)
5			Resetting adaptive values
6			Version configuration
7			Vehicle inform(euro.only)
8			Idle rpm adjust node
9			Resetting adaptive values
10		Chassis	HCU Air bleeding mode
11		Body	Active dtc information
12			History dtc information
13			Crashing information
14			Code saving
15			Normal coding
16			Neutralization
17			Code change
18			Key only matching
#	Make	System Type	Special Functions
1	Proton	Drive	Provisional DTCs
2			All Learned value
3			Read&Write learned value
4			Learned value reset
5			Test/limit value readout
6		Chassis	Provisional DTCs
7		Body	Diagnose mode start
8			Reminder reset
9			Next schedule reminder cancel
10			Extra reminder setting
11			Extra reminder cancel
12			Periodic reminder schedule set
13			Integrated value adjustment
14			Optional INT schedule setting